Behringer UMX250 Manuel d'utilisateur télécharger pdf (Page 8)

ENGLISH

U-CONTROL UMX250 User Manual

ASSIGN mode 4.2

As already mentioned in the preceding chapters, the ASSIGN

mode is a powerful tool which allows you to re-congure the

UMX250 to an extremely easy-to-use controller.

The fundamental logic of the assignment procedure was already

presented in Chapter 3 “Control elements and connections”.

Setting the GLOBAL CHANNEL4.2.1

MIDI channels are classied into two types: one GLOBAL

CHANNEL and 16 SINGLE CHANNELS.

The GLOBAL MIDI CHANNEL is a factory setting and

all MIDI instructions are sent over this channel: messages

of various control elements as well as note-on and note-off

messages. Please proceed as follows to modify the GLOBAL

MIDI CHANNEL:

Press the ASSIGN button and keep it pressed.1)

Press the GLOBAL key.2)

Release the ASSIGN button.3)

Now dene the GLOBAL CHANNEL by entering a number 4)

between 1 and 16 using the number keys. If you enter a

number greater than 16, your entry will be rejected.

Examples:

- If you want to enter channel 14, press keys

(1)

and

(4)

- To enter channel 7 press key

(7)

In order to conrm your selection, press the ENTER key. To 5)

discard your assignments either press the CANCEL button

or the ASSIGN button again. In either case the ASSIGN

LED goes out.

Ex works the GLOBAL CHANNEL is set to channel 1.

◊

Individual channel assignment4.2.2

The assignment of individual control elements to a certain

channel is useful if you want to control external devices indepen-

dently of one another.

Example:

You play synthesizer A over channel 2 from the keyboard,

while synthesizer B is controlled on channel 5 by a sequencer

software. Now you can control the lter frequency of device B in

real time using one of the eight rotary controls, and at the same

time continue playing device A without changes to the lter

frequency.

Press the ASSIGN button and keep it pressed.1)

Operate the control element whose channel shall be set to 2)

differ from the GLOBAL CHANNEL. If it is a controller

or a fader, move it briey. If it is a button, press it once.

Now theUMX250 “knows” which control element shall be

assigned to a SINGLE CHANNEL.

Release the ASSIGN button.3)

Press the SINGLE key.4)

Now dene the SINGLE CHANNEL by entering a number 5)

between 1 and 16 using the number keys. If you enter a

number greater than 16, your entry will be rejected.

Example:

- If you want to enter channel 11, press keys

(1)

and

(1)

- To enter channel 4 press key

(4)

Special case: If you want to assign the control element to

◊

the GLOBAL CHANNEL again, please press the 0 key next

to the ENTER key (instead of the number keys 1 to 9).

To nalize your settings, press the ENTER button. To 6)

discard your assignments either press the CANCEL button

or the ASSIGN button again. In either case the ASSIGN

LED goes out.

The channel set-up of all control elements of the UMX250 is

◊

based on the GLOBAL CHANNEL. This means that a control

element is always set to the GLOBAL CHANNEL until you

assign a different channel to it. Whenever you change the

GLOBAL CHANNEL you also change the channels assigned

to the various control elements!

GLOBAL CHANNEL assignment4.2.3

In comparison to the procedure described in the previous

chapter, the advantage of the method shown here is that you

have to press fewer buttons to make adjustments.

Press the ASSIGN button and keep it pressed.1)

Operate the control element whose GLOBAL CHANNEL 2)

shall be set.

Release the ASSIGN button.3)

Press the SINGLE-key.4)

Press the 0-key.5)

Press ENTER to conrm. Press CANCEL or the ASSIGN 6)

button again to discard your assignments. In either case the

ASSIGN LED goes out.

The PANIC key combination4.2.4

Imagine you have already worked several hours on a song and

suddenly one of your sound modules produces a “hanging note”.

If you execute a PANIC instruction, a sound module receiving

this instruction will be muted immediately.

Press the ASSIGN button and keep it pressed.1)

Press RESET ALL or NOTES OFF.2)

Release the ASSIGN button. The device automatically enters 3)

Play mode again.

The instruction chosen will be sent immediately after

◊

pressing one of the two buttons mentioned above.

1 2 3 4 5 6 7 8 9 10 11 12 13 ... 17 18

Commentaires sur ces manuels

Pas de commentaire

Behringer UMX250 Manuel d'utilisateur Page 8

Commentaires sur ces manuels