Behringer B-Control Deejay BCD3000 Manuel d'utilisateur télécharger pdf (Page 8)

8 B-CONTROL DEEJAY BCD3000 User Manual

The OUTPUT section

The [13] CUE A and CUE B buttons allow you to listen in on Deck A or B. Keep the

respective button pressed to feed the signal of Deck A or Deck B to the

Headphone output [14].

The [14] PHONES output (¼" stereo connector) is used for

connecting headphones.

The [15] PHONES VOL control lets you adjust the volume level of the

Headphone output [14].

The [16] PHONES MIX control is used to adjust the relation between the stereo

MASTER OUT and MONITOR OUT signal. When the control is turned fully left,

you hear the MONITOR OUT signal, and when turned fully right, you hear the

MASTER OUT signal.

The [17] KEY DECK A+B button is used to activate the “Key Lock” function of

the TRAKTOR 3 LE software. The “pitching” of a track usually changes both

the music’s speed (tempo) and pitch/key. The “Key Lock” function (or Master

Tempo) makes sure the pitch is retained. Find more on this topic in the PDF

manual of TRAKTOR 3 LE.

Set the volume of the MASTER output with the [18] MASTER OUTPUT control.

The [19] POWER ON-LED lights up when the BCD3000 is switched on.

The deck sections A and B

The control elements of decks A and B are the same. However, some of them are

grouped the opposite way round. We will therefore describe the elements to

only once. All of these control elements refer to the software functions which can

be “remotely” controlled from the BCD3000.

The [20] CROSSFADER is used to fade between deck A and deck B.

The [21] GAIN control allows you to adjust the deck signal to a nominal level.

Each deck features a 3-band equalizer ([22] HI, MID and LOW) with kill feature.

Thus, the signal can be attenuated to a much greater extent (-24 dB) than it

can be raised (+12 dB).

The KILL buttons, which are found below the EQ controllers, allow you

to cut out the relevant frequency range at the push of a button. This way

you can achieve interesting ﬁlter eﬀects. The function is also required for

beat juggling.

The [23] SET CUE button sets a cue point at the current position of the track

being played. This happens without interrupting playback. You can ﬁnd

information on the CUE function in Chapter 5.2.

SET LOOP[24] allows you to set the start and end points of a four-beat sequence

that is to be played back repeatedly (loop). The ﬁrst time this button is

pressed, the start point of the loop is set and the following four beats

are repeated as often as you like. Press the button a second time to stop

the loop.

RELOOP[25] is used to play a loop that you speciﬁed with SET LOOP

[24] beforehand. Press SET LOOP [24] once again to stop the loop.

SYNC[26] allows you to synchronize two tracks, which are running on Deck A and

B, by matching their speeds. The deck, which has its SYNC button pressed,

synchronizes itself automatically with the speed of the second deck.

The Scratch Wheel [27] [34] allows you to scratch while the deck is playing or

paused. Please press the SCRATCH button (LED lights up) in order to scratch.

The [28] VOLUME fader is used to adjust the volume level of the particular deck.

Press the [29] PLAY button to begin playback. Press this button a second time to

stop playback. By pressing PLAY again, playback continues from the point at

which it was stopped.

Every time playback is stopped, the cue point is placed at the current song

position. You can ﬁnd information on the CUE function in Chapter 5.2.

Press the [30] CUE button to stop playback and return to the last set cue point.

By keeping the CUE button pressed, the music begins at the cue point and

continues until you let go of the button. Then, the deck jumps back to the

cue point. You can ﬁnd information on the CUE function in Chapter 5.2.

BEND[31] buttons: Press the UP button (+) to increase the playback speed.

Press the DOWN button (–) to decrease the playback speed. This function

lets you match the beats of two playing tracks.

The Pitch fader adjusts the playback speed seamlessly.[32]

Use the [33] SEARCH buttons to move forward or backward in a song.

The function performed by the scratch wheel depends on whether the deck [34]

is in PLAY or PAUSE mode.

In PLAY mode, re-create the analog feel by using the wheel to nudge

(turn wheel to the right) or slow down (turn wheel to the left), allowing you

to easily match the speed of the current deck to the speed of the other

deck playing. Press the SCRATCH button in order for you to scratch with

the wheel.

In PAUSE mode, you can use the wheel to move back and forth through the

song. You can also scratch with the wheel by pressing the SCRATCH button.

The rear panel3.2

[40] [37] [35][38][39] [36]

Fig. 3.2: The rear-panel audio connectors of the BCD3000

MIC INPUT[35] . The MIC IN connector is the balanced XLR input for your

dynamic microphone.

The analog input A ([36] PHONO) is used for connecting a turntable.

Connect the ground cable on your turntable to the [37] GND screw on the

BCD3000 housing.

Analog input B. To connect a CD player or tape deck to this input, set the [38]

switch to LINE.

Connect the [39] MASTER OUTPUT to your power ampliﬁer. It provides the main

output signal, which can be adjusted with the MASTER control .

SERIAL NUMBER[40] .

1 2 3 4 5 6 7 8 9 10 11 12 13 ... 19 20

Commentaires sur ces manuels

Pas de commentaire

Behringer B-Control Deejay BCD3000 Manuel d'utilisateur Page 8

Commentaires sur ces manuels

Produits connexes et manuels pour Mélangeurs Behringer B-Control Deejay BCD3000