Behringer V-tone GMX212 Manuel d'utilisateur télécharger pdf (Page 6)

6 V-TONE GMX1200H/GMX212/GMX210/GMX112/GMX110 User Manual

1.3.3 Online registration

Please register your new BEHRINGER equipment right after your purchase

by visiting http://behringer.com and read the terms and conditions of our

warrantycarefully.

Should your BEHRINGER product malfunction, it is our intention to have it

repaired as quickly as possible. To arrange for warranty service, please contact

the BEHRINGER retailer from whom the equipment was purchased. Shouldyour

BEHRINGER dealer not be located in your vicinity, you may directly contact

one of our subsidiaries. Corresponding contact information is included in the

original equipment packaging (Global Contact Information/European Contact

Information). Should your country not be listed, please contact the distributor

nearest you. A list of distributors can be found in the support area of our website

(http://behringer.com).

Registering your purchase and equipment with us helps us process your repair

claims more quickly and eciently.

Thank you for your cooperation!

2. Control Elements

andConnections

Control elements of your V-TONE guitar amp are described in this section.

Allcontrols and connections are explained in detail, and we give you useful tips

on how to use them. An illustration of control elements with corresponding

numbering can be found on the separately included supplementary sheet.

Because models GMX112, GMX210, GMX212 and GMX1200H each feature two

identical MODELING CHANNELS, control elements (4) through (11) will only be

described once in the following section.

2.1 Front panel

(1) The connector labeled INPUT is the ¼“ jack input of your V-TONE. Use it

to connect your guitar. Use a commercially available ¼“ jack mono cable

(no DIY, ask your specialized dealer) with good mechanical and electrical

shielding to avoid unpleasant surprises during rehearsals or concerts.

(2) On the GMX110, the CLEAN control modies the volume of the

CLEANchannel in relation to the MODELING CHANNEL.

(3) Use the CHANNEL key to alternate between the two modeling channels

(except for the GMX110). The channel LED (5) lights up when the channel is

activated. On the GMX110, the CHANNEL key switches between CLEAN and

MODELING CHANNEL. CLEAN CHANNEL is active when the channel LED (5)

is not lit up. With all models you can also switch between channels using

the provided footswitch. A long hit (approx. 2 seconds) on the CHANNEL key

activates the guitar tuner.

(4) The DRIVE control determines the amount of distortion in the respective

MODELING CHANNEL. Using this, you can ideally adjust the VTONE pre-amp

to the output level of your guitar pick-up to achieve the desired amount

of distortion (depending on the amp, mode and speaker combination

youselected).

(5) The CHANNEL LED indicates the currently selected channel.

(6) Use the AMP switch to select one of the three guitar amps that orient

themselves on classic tube amps. You will surely recognize these classic

amp sounds as soon as you hear them. If you select TWEED, expect crystal-

clear, transparent sounds with dynamic bass. You get aggressive mids and

pressure-rich, inescapable assertiveness and endurance when you select

BRITISH. Rounder and more evened-out (yet still sophisticated) sounds can

be dialed up if you select CALIF.(ORNIAN); perfect for lead sounds!

(7) Use the MODE switch to choose one of three possible gain settings

(CLEAN,HI GAIN and HOT) you wish to use with the basic sound you selected

with the AMP switch.

(8) The SPEAKER switch oers the simulations of two classic guitar speakers:

4 x 12“ speaker in an enclosed casing (U.K.) and 2 x 12“ speaker in an open

casing (US). Additionally, we have included a frequency response correction

(FLAT), specially modied to go with V-TONE’s cabinet.

(9) The LOW control on the EQ section lets you cut or boost the bass frequencies.

(10) Use the MID control to cut or boost the mids.

(11) The HIGH control regulates the upper frequency range.

(12) If the tuner is activated, these LEDs (in connection with the FX display)

indicate your guitar’s tune. Activate the tuner by keeping the CHANNEL

pressed for roughly 2 seconds.

(13) The FX DISPLAY indicates either the program number of the preset you

selected or the value of the parameter dialed up using the FX control.

(14) Use the PRESET control to dial up one of the eect presets (between 01

and99). The preset you dialed up is loaded when you make no further

changes for about one second after dialing up that preset.

(15) Use the IN/OUT key to activate/deactivate the selected eect. When the

eect is activated, the LED located above the switch lights up. You can save

your own eect settings by keeping this key pressed for about 2 seconds

(also see section 4). The eect can also be activated/deactivated using the

provided footswitch.

◊ If the MIDI function is deactivated (see ch. 4.2), FX tracking

is active, i.e. a separate effect can be selected for each of the channels

of your V-TONE. FXT is explained in detail in section 4.1.

(16) The FX control adjusts the mix ratio between the original and the

eectsignal.

(17) The LEVEL control adjusts the volume of the respective channel.

AdjustLEVEL to achieve the desired volume balance between both channels.

◊ The GMX110 features no such control. However, use ( 2 ) to control the

volume of the CLEAN channel in respect to the MODELING channel;

use MASTER (19) to control the overall volume.

◊ The GMX112 and GMX210 feature the LEVEL control only on

MODELING CHANNEL 1. It controls the volume of the channel in

respect to the second channel.

(18) The PRESENCE control gives you an additional way to cut or boost the highs

(GMX212 and GMX1200H).

(19) The MASTER control regulates the overall volume as well as

headphonevolume.

(20) The POWER switch powers up your V-TONE. The POWER switch should

always be in the “O” position before you connect the V-TONE to the main

power source.

◊ Please note: The POWER switch does not fully disconnect the unit from

the mains power cord plug or extention cord. To disconnect the unit

from the main power source, pull out the main cord plug or appliance

coupler. When installing the product, ensure the plug or appliance

coupler is readily operable. Unplug the power cord when the unit is not

used for prolonged periods of time.

◊ GMX110’s POWER switch is located on the rear.

1 2 3 4 5 6 7 8 9 10 11 ... 22 23

Commentaires sur ces manuels

Pas de commentaire

Behringer V-tone GMX212 Manuel d'utilisateur Page 6

Commentaires sur ces manuels

Produits connexes et manuels pour Amplificateurs audio Behringer V-tone GMX212